Link at 10+ PSI ?

by **Fergus** » Thu, 29 Jan 2009 1:02 +0000

Ok here is my list.
Link ECU
MAP Sensor
Vac line
Keypad & cable
Knock Sensor
Air Temp Sensor
Injectors
Walbro Fuel Pump
IC

What else do I need :scratch:

Serial Cable & software.
A Better Diff.
??????

by **Steve** » Thu, 29 Jan 2009 1:20 +0000

What size injectors are you going for?

You don't need a Walbro, stock pump is fine.

You'll need a serial or usb link box + DataLogLab, laptop or PDA for tuning altho.. you could do the majority via the keypad if you don't mind inputting the fuel/timing tables (if your injectors aren't 440cc or 550cc).

Electronic Boost Controller

1.8 Diff (but can be left till the 1.6 gives up the ghost)

Stronger Clutch (Act clutch is good)

You'll have some rewiring to do too (ECU and injector harness).

Redline MTL in the gearbox

And... sort out your brakes ;-)

by **Fergus** » Thu, 29 Jan 2009 1:27 +0000

Ops I forgot to add in the AEM Wideband I have already.
I was thinking of the Rx injectors.

Yeah I had forgotten that larger injectors mean no need to change the pump.
Totally forgotten about the clutch to.

So I need an EBC.
Will the 1.8 Diff handle 10PSI ok ?

by **Fergus** » Thu, 29 Jan 2009 1:45 +0000

Can anyone recommend a good EBC ?

(edit) and a BOV :shock:

by **Steve** » Thu, 29 Jan 2009 2:25 +0000

FM has both, they work well.

RX7? 520cc or so? I'd recommend getting either 440cc or 550cc as there are 2 pretuned maps in the link which FM spent lots of rolling road time on. If you change the size/type of injectors you get into all sorts of messing about with dwell/cold starts/summer&winter starts/retuning most of the table to compensate (I've been through it with my 390cc injectors).

The 1.8 diff will handle it fine unless you reaaally abuse it.. you don't hear about too many 1.8 diffs breaking.

by **Fergus** » Wed, 04 Feb 2009 2:01 +0000

I just bought 4 NEW RC440cc injectors, loom and clips

by **Steve** » Wed, 04 Feb 2009 7:05 +0000

Nice one! Did you get them from RC?

The loom and connectors are the same as the '5s injectors, just be sure the loom is wired for sequential injection (2 new wires need to be run from the ECU to the loom).

Steve

by **Fergus** » Wed, 04 Feb 2009 7:25 +0000

FleaBay... http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... 0285346791

by **Steve** » Wed, 04 Feb 2009 10:17 +0000

cool! Same as my own, am still after a set of new o-rings for them before I install tho.

by **Fergus** » Thu, 05 Feb 2009 1:58 +0000

O-Rings...I know nadda about O-Rings except the metal ones, you can use the old ones if you put them in backwards/upsidedown etc, they last just as long that way as the original ones, they even work BETTER.
BUT if their rubber then I know nadda :shock:

by **Steve** » Thu, 05 Feb 2009 10:10 +0000

Def get a set of o-rings for the injectors (yup, rubber ones) .. oil em up before fitting or you could tear them.. last thing you'll want is a fuel leak after all your work! ;-)

by **Fergus** » Thu, 05 Feb 2009 10:33 +0000

Are these them.... http://www.mx5parts.co.uk/product_info. ... ts_id/1311

I've got temp and knock sensors on the way from the states right now.
How much boost are the 440cc injectors good for ? What's the limit etc ?

by **Fergus** » Thu, 05 Feb 2009 10:42 +0000

Also, about the 1.8 diff.
I'll be needing the 1.8 diff, half shafts and prop/drive shaft...is that all ?
What's all this about "long nose/short nose" stuff ?

by **Steve** » Fri, 06 Feb 2009 1:46 +0000

Fergus wrote:Are these them.... http://www.mx5parts.co.uk/product_info. ... ts_id/1311

I've got temp and knock sensors on the way from the states right now.
How much boost are the 440cc injectors good for ? What's the limit etc ?

Yeah, they are like those ones, but I think they are specific to the RC injectors (plus I think there are 3 per injector.. ).

As for boost.. depends on your setup, 15psi isn't unheard of.. see this page for info on setups and dynos : [url]
http://web.archive.org/web/200111070151 ... y/dyno.htm[/url]

Steve

by **Fergus** » Sat, 07 Feb 2009 10:51 +0000

What about a 1.8 LSD diff ? Are they any good ?


	Board index ‹ Performance & Mods ‹ Engine Mods ‹ Turbo Talk Change font size Print view


	Author Message Link at 10+ PSI ? by Fergus » Thu, 29 Jan 2009 1:02 +0000 Ok here is my list. Link ECU MAP Sensor Vac line Keypad & cable Knock Sensor Air Temp Sensor Injectors Walbro Fuel Pump IC What else do I need Serial Cable & software. A Better Diff. ?????? Fergus *** Posts: 1912 Joined: Mon, 30 Jul 2007 5:53 +0000 Location: Ireland Top by Steve » Thu, 29 Jan 2009 1:20 +0000 What size injectors are you going for? You don't need a Walbro, stock pump is fine. You'll need a serial or usb link box + DataLogLab, laptop or PDA for tuning altho.. you could do the majority via the keypad if you don't mind inputting the fuel/timing tables (if your injectors aren't 440cc or 550cc). Electronic Boost Controller 1.8 Diff (but can be left till the 1.6 gives up the ghost) Stronger Clutch (Act clutch is good) You'll have some rewiring to do too (ECU and injector harness). Redline MTL in the gearbox And... sort out your brakes Steve Site Admin Posts: 5526 Joined: Wed, 05 Mar 2008 10:16 +0000 Top by Fergus » Thu, 29 Jan 2009 1:27 +0000 Ops I forgot to add in the AEM Wideband I have already. I was thinking of the Rx injectors. Yeah I had forgotten that larger injectors mean no need to change the pump. Totally forgotten about the clutch to. So I need an EBC. Will the 1.8 Diff handle 10PSI ok ? Fergus * Posts: 1912 Joined: Mon, 30 Jul 2007 5:53 +0000 Location: Ireland Top by Fergus » Thu, 29 Jan 2009 1:45 +0000 Can anyone recommend a good EBC ? (edit) and a BOV Fergus * Posts: 1912 Joined: Mon, 30 Jul 2007 5:53 +0000 Location: Ireland Top by Steve » Thu, 29 Jan 2009 2:25 +0000 FM has both, they work well. RX7? 520cc or so? I'd recommend getting either 440cc or 550cc as there are 2 pretuned maps in the link which FM spent lots of rolling road time on. If you change the size/type of injectors you get into all sorts of messing about with dwell/cold starts/summer&winter starts/retuning most of the table to compensate (I've been through it with my 390cc injectors). The 1.8 diff will handle it fine unless you reaaally abuse it.. you don't hear about too many 1.8 diffs breaking. Steve Site Admin Posts: 5526 Joined: Wed, 05 Mar 2008 10:16 +0000 Top by Fergus » Wed, 04 Feb 2009 2:01 +0000 I just bought 4 NEW RC440cc injectors, loom and clips Fergus * Posts: 1912 Joined: Mon, 30 Jul 2007 5:53 +0000 Location: Ireland Top by Steve » Wed, 04 Feb 2009 7:05 +0000 Nice one! Did you get them from RC? The loom and connectors are the same as the '5s injectors, just be sure the loom is wired for sequential injection (2 new wires need to be run from the ECU to the loom). Steve Steve Site Admin Posts: 5526 Joined: Wed, 05 Mar 2008 10:16 +0000 Top by Fergus » Wed, 04 Feb 2009 7:25 +0000 FleaBay... http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... 0285346791 Fergus * Posts: 1912 Joined: Mon, 30 Jul 2007 5:53 +0000 Location: Ireland Top by Steve » Wed, 04 Feb 2009 10:17 +0000 cool! Same as my own, am still after a set of new o-rings for them before I install tho. Steve Site Admin Posts: 5526 Joined: Wed, 05 Mar 2008 10:16 +0000 Top by Fergus » Thu, 05 Feb 2009 1:58 +0000 O-Rings...I know nadda about O-Rings except the metal ones, you can use the old ones if you put them in backwards/upsidedown etc, they last just as long that way as the original ones, they even work BETTER. BUT if their rubber then I know nadda Fergus * Posts: 1912 Joined: Mon, 30 Jul 2007 5:53 +0000 Location: Ireland Top by Steve » Thu, 05 Feb 2009 10:10 +0000 Def get a set of o-rings for the injectors (yup, rubber ones) .. oil em up before fitting or you could tear them.. last thing you'll want is a fuel leak after all your work! Steve Site Admin Posts: 5526 Joined: Wed, 05 Mar 2008 10:16 +0000 Top by Fergus » Thu, 05 Feb 2009 10:33 +0000 Are these them.... http://www.mx5parts.co.uk/product_info. ... ts_id/1311 I've got temp and knock sensors on the way from the states right now. How much boost are the 440cc injectors good for ? What's the limit etc ? Fergus * Posts: 1912 Joined: Mon, 30 Jul 2007 5:53 +0000 Location: Ireland Top by Fergus » Thu, 05 Feb 2009 10:42 +0000 Also, about the 1.8 diff. I'll be needing the 1.8 diff, half shafts and prop/drive shaft...is that all ? What's all this about "long nose/short nose" stuff ? Fergus * Posts: 1912 Joined: Mon, 30 Jul 2007 5:53 +0000 Location: Ireland Top by Steve » Fri, 06 Feb 2009 1:46 +0000 Fergus wrote:Are these them.... http://www.mx5parts.co.uk/product_info. ... ts_id/1311 I've got temp and knock sensors on the way from the states right now. How much boost are the 440cc injectors good for ? What's the limit etc ? Yeah, they are like those ones, but I think they are specific to the RC injectors (plus I think there are 3 per injector.. ). As for boost.. depends on your setup, 15psi isn't unheard of.. see this page for info on setups and dynos : [url] http://web.archive.org/web/200111070151 ... y/dyno.htm[/url] Steve Steve Site Admin Posts: 5526 Joined: Wed, 05 Mar 2008 10:16 +0000 Top by Fergus » Sat, 07 Feb 2009 10:51 +0000 What about a 1.8 LSD diff ? Are they any good ? Fergus * Posts: 1912 Joined: Mon, 30 Jul 2007 5:53 +0000 Location:** Ireland Top


	Who is online Users browsing this forum: No registered users and 1 guest


	Board index The team • Delete all board cookies • All times are UTC [ DST ]

Link at 10+ PSI ?

Link at 10+ PSI ?

Who is online