What did you do to your MX5 today ?

[Sean]

Today,i was walking around my MX admiring her when i stood in some dog poop which was left by my white boxer dog next to the passenger side door.........is he trying to tell me something?!!

[leamyj]

Today,i was walking around my MX admiring her when i stood in some dog poop which was left by my white boxer dog next to the passenger side door.........is he trying to tell me something?!!

YEAH..DONT GET ME SNIPPED

JOHN

[sspecdave]

Got the 4 wheel alignment done today. Very happy everthing is now spot on. Guy that done tracking spent about 1.5 hours getting it set up as close to the original settings as he could (eunos roadster settings) and all measurements are well within tolerence from the computer print out.
Grand total 60 euro

[fabfiveferg]

60 blips is pretty good. Where did you get it done Dave? Mine is need of doing

[leamyj]

Hope to get the rest of the car t-cut this evening.. my arms are aching from last evenings session.

Anyone know where I'd get a decent buffer for reasonable spondoolix?
Been keeping an eye on the German stores.


John

[leamyj]

Hope to get the rest of the car t-cut this evening.. my arms are aching from last evenings session.
John

NAAAHHH.. got diddly squat done after all, forgot I had to go to a school meeting.. Maybe tomorrow evening

John

[Mise]

Finally got around to SPEND SOME TIME and some TLC on my Mazda
1.Washed
2.Waxed
3.Polished Alloys
3.Valeted inside
4.Stood back and went

YES

then took it for a burn BIG TIME ( New clutch just gone in !!

[sspecdave]

60 blips is pretty good. Where did you get it done Dave? Mine is need of doing

CLONMEL which may not be of use to ya!
This guy has all the identical equipment used in the nct test centres and guarantee's it will pass . He also used to work for the nct but setup on his own couple years back.

[MX5Steve]

60 blips is pretty good. Where did you get it done Dave? Mine is need of doing

CLONMEL which may not be of use to ya!
This guy has all the identical equipment used in the nct test centres and guarantee's it will pass . He also used to work for the nct but setup on his own couple years back.

oooh handy to know, whats the nmae of the place dave?

[MX5Steve]

Went to a seminar in shannon today drove the whole way back to waterford a 22°C roof down music blaring, lulvly jubbly.............ZOOM ZOOM ZOOM!!!!!!

Hey steve, hows about making this a permanent subject, " Today me and my mx-5 have mostly been doing ............"

[Sean]

Finally got around to SPEND SOME TIME and some TLC on my Mazda
1.Washed
2.Waxed
3.Polished Alloys
3.Valeted inside
4.Stood back and went

YES

then took it for a burn BIG TIME ( New clutch just gone in !!

Thanks for the burn in your MX today Mise! ............she is looking really fine!

[Ivan]

Hope to get the rest of the car t-cut this evening.. my arms are aching from last evenings session.

Anyone know where I'd get a decent buffer for reasonable spondoolix?
Been keeping an eye on the German stores.


John

i got one in halfords, 50 euro. Well worth it

[leamyj]

Hope to get the rest of the car t-cut this evening.. my arms are aching from last evenings session.

Anyone know where I'd get a decent buffer for reasonable spondoolix?
Been keeping an eye on the German stores.


John

i got one in halfords, 50 euro. Well worth it

Thanks Ivan, will have a look.
BTW you coming on the run on 25th ... your boxster would love the route I have planned..mind you , nothing as spectacular as the Alps

John

[mx5ash]

Well i got the new tyres fitted and started to polish the car after quite a long time of standing it was getting a little un-shiny.
got the boot and rear wings done before it rained.
mmmm shiny

[leamyj]

got the boot and rear wings done before it rained.

Don't mention the "R" word,

John