Login    Register

wouldn't go into gear with engine on

Welcome to MX-5 Ireland. Pop in and say hello
  • Author
    Message

wouldn't go into gear with engine on

Postby Steve » Wed, 22 Feb 2017 1:22 +0000

I was moving the MX5 this morning, its been sitting still for a few months. I started the car but couldn't get it into any gear. Turned car off, no problem getting it into gear, so it wasn't the slave or master.
Ended up putting it into reverse gear and starting it with the clutch in, it jumped back initially (as I'd expected) then idled normally.
Am I right in thinking that the friction disk had stuck to the flywheel due to lack of use?
Steve
Site Admin

User avatar
 
Posts: 5524
Joined: Wed, 05 Mar 2008 10:16 +0000

Re: wouldn't go into gear with engine on

Postby MX5Spares » Wed, 22 Feb 2017 6:26 +0000

Hi Steve, common enough for disc to be stuck to flywheel or pressure plate.Be fine now.
MX5Spares
*****
 
Posts: 2303
Joined: Wed, 22 Sep 2010 4:59 +0000
Location: dublin,

Re: wouldn't go into gear with engine on

Postby Steve » Wed, 22 Feb 2017 10:02 +0000

nice one.
Also, my clutch pedal is engaging almost on the floor, not sure if it was always that way and I just need to get used to it again ;-) Must bleed it anywho.
Steve
Site Admin

User avatar
 
Posts: 5524
Joined: Wed, 05 Mar 2008 10:16 +0000

Re: wouldn't go into gear with engine on

Postby MX5Spares » Fri, 24 Feb 2017 8:14 +0000

Check fluid level and have look at slave cyl in particular for leaks.If not then master cyl.Possibly in the cabin behind the clutch pedal area/carpet etc.Bleed it if not and monitor the level etc
MX5Spares
*****
 
Posts: 2303
Joined: Wed, 22 Sep 2010 4:59 +0000
Location: dublin,

Re: wouldn't go into gear with engine on

Postby Steve » Sat, 25 Feb 2017 11:02 +0000

yeah, had checked levels and all look ok plus fluid still not black. Might just swop it out while I'm at it.
thanks
Steve
Site Admin

User avatar
 
Posts: 5524
Joined: Wed, 05 Mar 2008 10:16 +0000

Re: wouldn't go into gear with engine on

Postby MX5Spares » Sat, 25 Feb 2017 5:36 +0000

Hi Steve , sometimes it hard to bleed the system but if there is still fluid in it may be ok.Fully drained they can be awkward.I have old master cyl cap which I drilled a hole and popped in car tubeless valve and now I can pressurise the system slightly with slave cyl nipple open and works a treat every time
MX5Spares
*****
 
Posts: 2303
Joined: Wed, 22 Sep 2010 4:59 +0000
Location: dublin,

Re: wouldn't go into gear with engine on

Postby Steve » Sun, 26 Feb 2017 1:06 +0000

cool thanks.
The Master was "bench" bled when I put it in and have a straight run clutch hose from master to slave (no pigtail bit), so am hoping it'll bleed easily enough.
Steve
Site Admin

User avatar
 
Posts: 5524
Joined: Wed, 05 Mar 2008 10:16 +0000

Re: wouldn't go into gear with engine on

Postby MX5Spares » Sun, 26 Feb 2017 2:05 +0000

Ah ,probably will bleed easily then
MX5Spares
*****
 
Posts: 2303
Joined: Wed, 22 Sep 2010 4:59 +0000
Location: dublin,

Re: wouldn't go into gear with engine on

Postby Johnny » Mon, 27 Feb 2017 12:28 +0000

Steve, where did you source that straight run clutch hose from master to slave you mention above. Reason I ask is that mine wouldn't go into gear after about a week up on ramps doing various jobs. Turned out clutch fluid reservoir was more or less empty. Checked slave and master cylinder and both seemed fine. Filled up with fluid and pumped clutch and see that its weeping from that flexible clutch hose where it joins that flat square bracket before lower steel line heads on down to the slave. Looks like a right pain to get at. Was wondering why they run the piping over and back along the firewall before going down to the slave, as both master and slave are on the same side of the car. Anyway what you mention makes sense, so was thinking of going this route if I knew what type of hose to get (length etc), fittings I might need, and where to get it. Is it same for mk2 as mk1? Sorry for kinda hijacking thread.
Johnny
**
 
Posts: 45
Joined: Tue, 25 Feb 2014 1:45 +0000
Location: Co.Galway

Re: wouldn't go into gear with engine on

Postby Merlot man » Mon, 27 Feb 2017 9:15 +0000

Steve wrote:cool thanks.
The Master was "bench" bled when I put it in and have a straight run clutch hose from master to slave (no pigtail bit), so am hoping it'll bleed easily enough.

Ya that's the way I did mine on the mk2
I think I got the straight SS hose from a group buy on nutz but I think mx5 parts do them as well but be sure you get the hose from the master to the slave not just a SS hose to replace the existing rubber hose and keeping the pig tail :shock:
Ring them if your not sure
Brian
]96 na Merlot edition. sold
99 nb 10th anniversary
93 na s ltd
Merlot man
****
 
Posts: 940
Joined: Wed, 02 Jun 2010 8:16 +0000
Location: Co Clare,Ireland

Re: wouldn't go into gear with engine on

Postby Johnny » Mon, 27 Feb 2017 11:51 +0000

Thanks brian, think http://www.moss-europe.co.uk/hose-clutc ... 08121.html is what I'm after
Johnny
**
 
Posts: 45
Joined: Tue, 25 Feb 2014 1:45 +0000
Location: Co.Galway

Re: wouldn't go into gear with engine on

Postby Steve » Tue, 28 Feb 2017 12:52 +0000

I bought mine through a group buy on here a number of years ago, but that line looks exactly the same.
V.quick and easy to fit (and you can pull all the old line).
Steve
Site Admin

User avatar
 
Posts: 5524
Joined: Wed, 05 Mar 2008 10:16 +0000

Re: wouldn't go into gear with engine on

Postby Johnny » Tue, 28 Feb 2017 1:54 +0000

Good stuff, thanks Steve.
Johnny
**
 
Posts: 45
Joined: Tue, 25 Feb 2014 1:45 +0000
Location: Co.Galway

Re: wouldn't go into gear with engine on

Postby Real Rayzor » Tue, 28 Feb 2017 10:05 +0000

You can get the clutch line at www.freakyparts.co.uk I was just researching it last week.
2002 MK2.5 Sunlight Silver (sold)

1992 MK1 V-Spec. Brilliant Black, Fully Restored
Real Rayzor
****
 
Posts: 700
Joined: Fri, 15 Aug 2014 10:38 +0000

Re: wouldn't go into gear with engine on

Postby Steve » Wed, 01 Mar 2017 10:51 +0000

some great stuff on that site, hadn't seen these before :
http://www.freakyparts.co.uk/epages/es1 ... rade_Front
Steve
Site Admin

User avatar
 
Posts: 5524
Joined: Wed, 05 Mar 2008 10:16 +0000

Next

Return to General chat

Who is online

Users browsing this forum: No registered users and 12 guests

cron